Info Links
 InGaAS spectrometer
 getSpec COLOR
 CCD spectrometer

   News
 






Informationen in deutsch





Informations en français





Информация на русском языке




Line Arrays for Miniaturized Spectrometers



Request for information

Line arrays are detectors with several individual readable sensitive areas, so-called pixels (picture elements), arranged in one straight line. They can be seen as "black boxes" transforming a spatially light distribution, in case of spectrometers the spectrum focus line, into a signal voltage or current distributed in time. This sequential output signal, the video signal, is further proceeded, mainly with an analog digital conversion as the first step. The main parameters of line detectors are the following:
    • Pixel number - the number of pixels arranged in the line
    • Pixel dimensions - the pixel width and height [µm]
    • Pixel pitch - the distance between the centers of two pixels [µm]
    • Sensitivity - the wavelength dependent ratio of electrical signal output to the optical signal input [e.g. V/lxs]
    • Wavelength range - the range of wavelengths where the detector can "see" radiation [nm]
    • Dark signal - the output signal without illumination of the detector [e.g. mV]
    • Saturation exposure - the illumination level, at which the output signal stays constant with increasing illuminance
    • Linearity range - the illuminance range where the electrical signal output is proportional to the impinging energy
    • Dynamic range - the range in which the detector is capable of accurately measuring the input signal [10x],
    • Pixel non-uniformity - the output signal difference of the pixels under same illumination conditions P [%]
Types of Line Arrays
Currently, there exist three different types of line arrays, which are used in spectrographs: CCD, photodiode and CMOS arrays. They differ in their distinct production technologies and their parameters.

CCD Arrays
Principle of Operation CCDs are array detectors with metal-oxyde capacitors (photogates). During the illumination by the spectrum focal line a charge (electron - hole pairs) is produced under the gate. A potential well is created by applying a voltage to the gate electrode. The charge is confined in the well associated with each pixel by the surrounding zones of higher potential (see detail in the next figure).
The read out of the array is proceeded by a charge transfer by means of varying gate potentials according to special clock schemes. The charges of the pixels are transfered simultaneously to the shift register(s), followed by a sequential transfer to the output section, where the charge is converted into a proportional voltage. The node doing this is first set to a reference level (clamp level) and afterwards to the signal level. The difference is used as the final signal. This technique is called Correlated Double Sampling (CDS) and allows a significant reduction of the system noise.


There exists a wide variety of CCD arrays from several producers. The Sony ILX series is often applied in spectroscopy. Other types are the TCD 1201D of Toshiba and the S 703x series of Hamamatsu. The latter has not only one pixel line but also 122. It can be used in the so-called line-binning mode. The signals of each pixel row in the direction perpendicular to the spectrum are additionally combined to create a greater pixel height.


Photodiode Arrays (PDA)
Principle of Operation

Photodiode arrays consist of several photodiodes arranged in a line. The light energy impinging on a diode generates a photocurrent, which is integrated by an integration circuitry associated with this pixel. During a sampling period the sampling capacitor connects to the output of the integrator through an analog switch.




There exist two different types of photodiode arrays which differ by kind of their output signal.Current output arrays supply the recharge current of the depletion layer capacity as measuring signal. Therefore, an additional integrator is necessary. The relation between the peak value of this current and the integral is poor, so read out electronics based on the reading of the peak value are of lower quality. Especially with low saturation charge, it is difficult to measure the output correctly. A value of 1 pC equals about 107 electrons, with an electronic resolution of 16 bit one LSB is represented by only 1 000 electrons.

Voltage output arrays have the integrator on board and deliver a photon flux proportional voltage for the measurement. This causes fewer problems with the read out electronics.

CMOS Arrays
Principle of Operation

CMOS arrays also use MOS structures as pixels like the CCD arrays. The basic difference is, that the charge-to-voltage conversion takes place directly in the pixel cell. This conversion consists again of two steps-the photon-electron and the charge (electron)-voltage conversion. This difference in read out technique has significant implications for the sensor architecture, capabilities and limitations. The following figure shows the scheme of a CMOS line array.


CMOS arrays show better sensitivity than CCD' s because it is easier to produce low power high gain amplifiers in CMOS technology.


Criteria of Selection for a Specific Application
As stated above, there are many parameters to consider for a proper selection of a line array for a specific application. Furthermore, it is necessary to weight the significance of the parameters because there is often no ideal choice possible.

Wavelength Range and Sensitivity
The detectable wavelength range of silicon-based arrays extends from 200 to 1100 nm, above this limit the photon energy is lower than the band gap energy. For longer wavelengths, InGaAs semiconductor material is used (up to 1.7 µm). Such arrays are relatively expensive. Furthermore, Si line arrays with anti Stokes Phosphor coatings are available. They are suited for the wavelength range up to approximately 1600 nm (depending on the material).
If we consider only silicon arrays there are also differences between the different types of arrays caused by the set-up and technical treatment. Mainly the extend of sensitivity in the range below 380 nm and above 800 nm differs significantly. The technical treatment. Mainly the extend of sensitivity in the range below 380 nm and above 800 nm differs significantly. The in the system detector, arrays in spectrometers are often used windowless. The following figure shows the relative sensitivity of several line arrays.


The periodic modulation in many sensitivity curves is caused by white light interference on thin layers in the sensitive area and can be avoided by antireflexion coatings. Typical absolute sensitivity values of different line arrays are shown in the following table:


Line ArrayTypical Sensitivity
Hamamatsu S546x series5.3 V/(lx s)
Sony ILX 5x1 series200 V/(lx s)
TAOS TSL 140x series25 V/(µJ/cm²)
Toshiba TCD 1201D80 V/(lx s)
Melexis MLX902551.3 V @ 10µW/cm² @ 0.7 ms
Reticon L series2.9 10-4 C/(J cm²)


Pixel Dimensions (pitch and height)
The pixel dimensions are an essential criterion for the selection of an array. The pixel width and pitch influence the digital resolution of a spectrometer and stand in relation to its optical resolution. Furthermore, it is necessary to adapt the pixel height to the height of the spectrum image. If the pixel height is too low, a part of the signal is lost and the efficiency of the system is low. On the other side a pixel height much larger than the spectrum height ends in an unwanted increased stray light influence. Some two - dimensional arrays allow a line binning for the virtual creation of a bigger pixel height.
The pixel line has to be precisely adjusted to the spectrometer focal line to avoid a strong thermal drift of the intensity output. Therefore, getSpec.com offers a special light source JLQ 1, which simultaneously emits three wavelength ranges in the blue, green and red into one fiber. The three outputs are controllable, this can be used with a precise mechanical positioning of the array in 3 directions (parallel and perpendicular to the pixel line as well as the angle between spectrum and pixel line) for a precise adjustment.

Dark Output
The dark output is a small electrical output of the line array without incident light. It is caused by thermal generation of carriers in the light sensitive elements, mainly due to Si . SiO2 interface states. It has a strong correlation with the operation temperature. The dark output doubles for every temperature increase of 6 ... 10 K. Therefore, line arrays are cooled in low light level applications, e.g. in astronomic measurements. Furthermore, the dark output depends on the integration time. Therefore, it is necessary in spectroscopic measurements to proceed a dark measurement at the same integration time which is used for the spectrum measurement. This can be done by a mechanical shutter or with a switched off light source.
The dark output level of the spectrometer electronics has a relative niveau. It can be moved by the choice of gain and offset settings.

Saturation and Linearity Range
Saturation exposure is that level of photon intensity where the photon signal of the detector is no more dependent on the incident light flux. The value depends on the doping of the detector material. A rule of thumb is that a good linearity is achieved with photodiode and CCD arrays modulated between 0 and approximately 75 % of the saturation charge (exposure). Above this value the non-linearity raises significantly. The following figure shows the linearity behavior of a current and a voltage output photodiode array.

The saturation exposure is given in the array data sheets, [mlx× s] and [nJ/cm2] are used as units, depending if it is seen from a photometric or a radiometric point of view. The following table shows some values:


Line ArrayTypical Saturation Exposure
Hamamatsu S390x series180mlx s=26,3nJ/cm² @550nm
Hamamatsu S392x series220mlx s=32,1nJ/cm² @550nm
Hamamatsu S837x series145/570mlx s=13,1nJ/cm² @550nm
Sony ILX 5x1 series40mlx s=5,8nJ/cm² @550nm
TAOS TSL 140x series92...140nJ/cm²
TAOS TSL 1301series7nJ/cm²
Reticon L series35nJ/cm²
PVs ELIS-1024800..6400Ke- fullwell (dep. from selected pixel width)


Noise and Dynamics

There are two main categories of sources, which generate noise in a line array.

1. Fixed pattern noise: It consists of the dark noise and read out noise (e.g. due to internal switching). The fixed pattern noise is constant when the read out conditions are fixed and the integration time is not changed. So it is possible to eliminate it by subtraction from the measured signal.

2. Random noise: It is traceable to erroneous fluctuations of voltage, current or electrical charge, which are caused in the signal output process. If the fixed pattern noise is subtracted, the random noise determines the lower limit of light detection or the lower limit of the system dynamic range.

The dynamics is that range in which the detector is capable of an accurately measurement of the signal and is defined as the maximum detectable signal divided by the minimum signal level. The maximum detectable signal is limited by the detector saturation, the minimum signal by the noise of the system. The dynamics depends on the integration time due to the thermal generation of noise.
Every kind of photon detectors only reaches a typical dynamics. Standard CCD arrays, like the Sony ILX 511, show a dynamics of 250 ... 300, related to full scale driving. If the spectrum has also regions with lower signal levels, the dynamics becomes even lower in these regions. The dynamics of photodiode arrays is much higher. It depends on the operation regime and is determined by the analog multiplexer on chip and the integrators. Dynamics values of > 3 104 can be reached with the Hamamatsu S39XX photodiode array series at room temperature, if it is used with a low noise integrator amplifier and a subsequent high performance 16 bit ADC. Photodiode arrays with integrator on board show a lower dynamics in main cases. An essential condition for a high dynamics is a high saturation charge of the array. In case of minimum speed demanding applications it is possible to increase the dynamics by averaging.

Temperature Drift of Sensitivity and Dynamics

There are two effects, which cause a significant temperature dependence of the detector sensitivity: The absorption coefficient increases slightly with temperature. This effect increases the IR efficiency, but conversely decreases the UV efficiency. The second more significant effect is the exponential increase of the thermally excited electron-hole pairs with temperature. This leakage current doubles every 6 ... 10 K increase in temperature, connected with a raising noise.

Pixel Non-uniformity

The individual pixels of an array have different sensitivities caused by crystal flaws in the substrate and slight local variations in the wafer process. This uniformity is measured during a uniform illuminance of the sensitive area (50 % of saturation exposure) and calculation of the maximum deviation from the average value.Often the pixel non-uniformity is not of interest, especially if spectrometric systems are referenced. Thus the specific pixel differences are included in this reference.

Integration Time

The integration time is the main parameter for the user to adapt the modulation of a spectrometric system to the signal level of the measurement. In many applications it is necessary to have a linear relation between the integration time and the signal, especially in radiometric measurements.

Image lag

The remain of charges on the PD/ CCD capacity or integrator is called image lag. It causes a virtual subsequent exposure if a dark measurement was done after a light measurement. Especially at CCD. s, which came into saturation, several following read out cycles are necessary before the measurement results can be used.



Aspects of Read out Electronics
Types of Video Signals

The classical video signal originates from the TV technologies. The defined voltages are 1 V for the synchronisation level, 0.75 V for black and 0 V for white. This video signal is called negative. Furthermore, all video signals have a positive offset voltage shifting the levels to higher values. CCD, like standard types of Sony (ILX series) and Toshiba are designed according to this classic standard.





Negative video signals often offer a so-called clamp level, which allows to set back the integrator to a defined offset voltage. So it is possible to use the clamp signal for a technique called correlated double sampling (CDS). One capacitor is loaded with the black level, the other one with the active video signal. The combination of both capacitors subtracts the charges. The result is a positive video signal for the ADC. Another solution uses two conversions of the black level and the active video signal and a following difference operation. This solution is much slower than the first one. The AD conversion is mainly based on a positive ADC related to 0 V. Therefore, a positive video signal offers the advantage of a much simpler subsequent AD converter. Furthermore, an additional noise due to further amplifiers is avoided. Main arrays, which have the integrator on board, offer a positive signal. Examples are the S837X series of Hamamatsu, the TSL series of TAOS and the arrays of Melexis and IC Haus.




Components of Line Array Read Out Electronics

A read out electronics for line arrays consists of the following main parts:

Timing: The electronics needs to generate the necessary clock pulses for the array. These pulses differ from array type to type.
Drive circuit: It serves for the operation of the shift registers.
Signal processing circuit: It serves for the CDS and the amplification.
AD converter: It transforms the analog signal to a digital level. Processor: It controls all processes and can be used for a precalculation of raw data.
RAM memory: There can be stored system data (e.g. the pixel . wavelength fit . see chapter 1.2.7. or intensity calibration data - see chapter 3.4.) and measured data (e.g. dark signal or reference signal).
Interface driver circuits: They manage the data transfer via different interfaces (e.g. USB, RS 232, parallel, CAN).




Reduction of Image Lag
An avoidance or significant reduction of the image lag effect can be reached by a continuous read out of the array, also before the start of the real integration time. JETI. s electronic solution applies a fast scan modus, which is used to remove the remaining charge carriers in a short time. A disadvantage of this technique is that the pixels, which are read out first, have a slightly shorter integration time. Another technique is to read out the array continuously. In this case the measurement will be distorted after saturation. The fast scan mode results in a "cleaner" photo capacitor.







getSpec.com offers several read out electronics for different line arrays. Some types are suited for more than one detector type, e.g. the electronics, shown in the following figure. It is suited for Hamamatsu S392x and S546x series, TAOS TSL 140x series, TSL 1301, iC Haus iC-LF 1401 and Melexis MLX 90255.


back to the general spectrometer specifications


Last change 08/15/2007 02:57 PM
Copyright (c) getAMO 2024